Post by super143 on Nov 12, 2018 7:00:20 GMT
Solution for fixing Canon mg5220 b200 error :
Error means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below:
Solution 1:
Disconnect the power cable from the printer.
Wait 1 hour.
Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unit
Check Cable connection especially the carriage FFC
Solution 3:
Turn off the power
Open the panel
Turn on the power
Wait for print carriage to start moving to the left.
Let it go past half way
Before print carriage reaches left hand side shut the cover.
Leave the Printer turned on
Solution 4:
Unplug the power cable.
Open the printer
Push the whole print head mechanic to the center
While the printer still open, plug the power and turn it ON.
When the printhead still moving and is going to the very LEFT, close the cover.
Wait until its boot up.
Solution 5
My Canon MX860 locked up with the B200 error when I continued printing without black ink. I removed printhead as described elsewhere and carefully flushed with hot tap water until no further ink waste was present. Reinstalled, but this did not resolve the B200 message and lockout.
Removed printhead again and this time removed 2 small screws (with jeweler's scredriver) on printhead to dimantle it. Use care to protect the ribbon cable. Do not try to remove this cable. You will see a complex rubber gasket. Remove this and clean with hot water. Set aside.
With screws removed, this will give access for more cleaning of the ink passages. Used hot water, then isopropal alcohol to wash, and finally a small (1/4") soft rubber tube to gently blow out water/alcohol from the printhead body. Be careful to not touch or push on the ink jets (little metal strips - large set for color; second set for black printing). Dried parts and reassembled. Carefully replace the gasket so that it fits over the plastic tips of the several ink ports.
Error B200 has disappeared
Ran printer maintenance from the PC: head deep cleaning, regular cleaning 3 times and head alignment check. Gradually print quality has been restored as ink has flowed into the printhead cavity and to the ink jets.
For More Information : Canon Tech Support
Error means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below:
Solution 1:
Disconnect the power cable from the printer.
Wait 1 hour.
Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unit
Check Cable connection especially the carriage FFC
Solution 3:
Turn off the power
Open the panel
Turn on the power
Wait for print carriage to start moving to the left.
Let it go past half way
Before print carriage reaches left hand side shut the cover.
Leave the Printer turned on
Solution 4:
Unplug the power cable.
Open the printer
Push the whole print head mechanic to the center
While the printer still open, plug the power and turn it ON.
When the printhead still moving and is going to the very LEFT, close the cover.
Wait until its boot up.
Solution 5
My Canon MX860 locked up with the B200 error when I continued printing without black ink. I removed printhead as described elsewhere and carefully flushed with hot tap water until no further ink waste was present. Reinstalled, but this did not resolve the B200 message and lockout.
Removed printhead again and this time removed 2 small screws (with jeweler's scredriver) on printhead to dimantle it. Use care to protect the ribbon cable. Do not try to remove this cable. You will see a complex rubber gasket. Remove this and clean with hot water. Set aside.
With screws removed, this will give access for more cleaning of the ink passages. Used hot water, then isopropal alcohol to wash, and finally a small (1/4") soft rubber tube to gently blow out water/alcohol from the printhead body. Be careful to not touch or push on the ink jets (little metal strips - large set for color; second set for black printing). Dried parts and reassembled. Carefully replace the gasket so that it fits over the plastic tips of the several ink ports.
Error B200 has disappeared
Ran printer maintenance from the PC: head deep cleaning, regular cleaning 3 times and head alignment check. Gradually print quality has been restored as ink has flowed into the printhead cavity and to the ink jets.
For More Information : Canon Tech Support